Can I Set Up a Tub Myself? Factors to Consider As Well As Steps
Can I Set Up a Tub Myself? Factors to Consider As Well As Steps
Blog Article
The content listed below pertaining to Tools You Need to Install a New Bathtub is seriously engaging. Check it out yourself and figure out what you think about it.
Setting up a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard task. If the old tub is readily available, the job can move immediately; if you have to open a wall to remove the old tub as well as position the new tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed task, it is much better to think about employing one prior to you begin. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly aid you set up a new tub in your restroom if you have already bought a brand-new bathtub as well as don't need to change the arrangement of your previous water pipelines.
Your devices as well as material checklist need to make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous kind needs to be connected to the tap ends initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using both wood boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four tiny points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, repair the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub needs to wait till the bath tub has actually been utilized a minimum of once as this will settle it into its final placement.
Planning for the Installment
First of all, the supporting structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily readily available on the marketplace. It is suggested to fit the tiles utilizing water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Hopefully you enjoyed our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for taking time to browse our posting. Do you know another person who is interested by the topic? Do not hesitate to promote it. Thanks a lot for going through it.
Book Instantly
Report this page